Yamaha YZ125 2018 Wartungsplan
Der folgende Wartungsplan für die Yamaha YZ125 (2018) enthält die vom Hersteller empfohlenen Wartungsintervalle für allgemeine Wartung, Kühlmittel, Öl, Zündkerzen, Antriebskettenpflege, Luftfilter, Reifen und Bremsflüssigkeit. Die Intervalle werden standardmäßig in Kilometern angezeigt und können auf Meilen umgestellt werden.
124ccHubraum
37Wartungspunkte
Offizielles Herstellerhandbuch
Quelle: ManualsLib (Yamaha Owner's Service Manual scan) (dieses Dokument deckt die Modelljahre 2000–2025 ab): manualslib.com
Vollständiger Wartungsplan
| Aufgabe | Intervall | Schwierigkeit | Hinweise |
|---|---|---|---|
| Piston pin & small-end bearing inspection & replacement | Alle 2 Betriebsstunden | Fortgeschritten | Inspect piston pin and connecting-rod small-end needle bearing for damage or wear; replace as required. |
| Transmission inspection & bearing replacement | Siehe Hinweise | Fortgeschritten | Inspect transmission gears and shafts for damage; replace bearings as required. |
| Shift fork, shift cam & guide bar inspection | Siehe Hinweise | Fortgeschritten | Inspect shift forks, shift cam and guide bar for wear or damage. |
| Rotor nut (flywheel) retightening | Alle 12 Betriebsstunden | Einfach | Retighten the flywheel/rotor nut to specified torque. |
| Crankshaft inspection & cleaning | Alle 12 Betriebsstunden | Experte | Inspect crankshaft for carbon deposits and damage; clean. |
| Coolant replacement | Alle 24 Monate | Einfach–Mittel | Drain and replace engine coolant. |
| Brake pad replacement | Siehe Hinweise | Mittel | Replace front and/or rear brake pads. |
| Front fork dust seal cleaning & lubrication | Alle 2 Betriebsstunden | Mittel | Clean fork dust seal and lubricate with lithium-soap-based grease. |
| Fork protector guide replacement | Siehe Hinweise | Einfach | Replace fork protector/guard seals. |
| Rear shock spring seat replacement | Alle 12 Monate | Mittel | Replace the rear shock spring seat. |
| Wheel bearing inspection, lubrication & replacement | Alle 7 Betriebsstunden | Mittel | Inspect wheel bearings for looseness; lubricate with lithium-soap-based grease. Replace worn bearings. |
| Transmission oil change | Alle 500 km (erstmals bei 2 km) · Alle 12 Betriebsstunden | Einfach | Drain and replace transmission/engine oil (Yamalube 4 (10W-30) or SAE 10W-30 SE motor oil). |
| Piston inspection, cleaning & replacement | Alle 2 Betriebsstunden · Ersetzen alle 12 km | Fortgeschritten | Inspect piston crown for carbon deposits, cracks, or damage; clean carbon. Replace piston, piston pin and small-end bearing as a set when worn. |
| Piston ring inspection & replacement | Alle 2 Betriebsstunden · Ersetzen alle 7 km | Fortgeschritten | Check piston ring end gap; inspect rings for damage. Replace rings when end gap exceeds service limit. |
| Cylinder head inspection, cleaning & retightening | Alle 2 Betriebsstunden | Mittel | Inspect cylinder head for carbon deposits and clean (decarbon); check head gasket condition; retighten cylinder head nuts to spec. |
| Cylinder bore inspection, cleaning & replacement | Alle 2 Betriebsstunden | Experte | Inspect cylinder bore for score marks and wear; clean. Rebore or replace cylinder as required. |
| Power valve (YPVS) inspection, cleaning & decarbonization | Alle 2 Betriebsstunden | Mittel | Inspect YPVS power-valve mechanism and exhaust port for carbon deposits, cracks or damage; clean/decarbonize. |
| Clutch inspection, adjustment & replacement | Alle 2 Betriebsstunden | Mittel | Inspect clutch housing, friction plates, clutch plates and springs for wear or damage; adjust. Replace worn components as required. |
| Muffler/exhaust inspection, cleaning & retightening | Alle 2 Betriebsstunden | Einfach | Inspect exhaust pipe/muffler for carbon deposits; clean. Retighten muffler mounting bolts. |
| Carburetor inspection, adjustment & cleaning | Alle 2 Betriebsstunden | Mittel | Inspect carburetor settings and check for obstructions; adjust and clean. |
| Spark plug inspection, cleaning & replacement | Alle 2 Betriebsstunden | Einfach | Inspect spark plug condition and gap; clean and regap (NGK BR9EG). Replace as required. |
| Drive chain lubrication, slack & alignment check / replacement | Alle 2 Betriebsstunden | Einfach | Check drive chain slack, alignment and condition; lubricate with chain lube. Chain slack spec: 48-58 mm (1.9-2.3 in). Replace chain as required. |
| Coolant level, hose & radiator cap inspection | Alle 2 Betriebsstunden | Einfach–Mittel | Check coolant level and for leakage; inspect hoses for cracks/damage; check radiator cap spring operation. |
| Outside nuts & bolts retightening (torque-check points) | Alle 2 Betriebsstunden | Einfach | Retighten chassis/engine torque-check-point nuts and bolts per the Torque-Check Points list. |
| Air filter cleaning, oiling & replacement | Alle 2 Betriebsstunden | Einfach | Clean foam air filter element with solvent and re-oil with foam air-filter oil. Replace element as required. |
| Frame cleaning & inspection | Alle 2 Betriebsstunden | Einfach | Clean frame and inspect for cracks or damage. |
| Fuel tank & fuel cock cleaning & inspection | Alle 7 Betriebsstunden | Einfach | Clean and inspect fuel tank and fuel cock. |
| Brake lever/pedal adjustment, pivot lube & disc/fluid inspection | Alle 2 Betriebsstunden | Mittel | Adjust brake lever position and pedal height; lubricate lever/pedal pivot points (after washing the motorcycle or riding in rain); check brake disc surface and fluid level/leakage; retighten disc bolts, caliper bolts, master-cylinder bolts and union bolts. |
| Front fork inspection, adjustment & oil/seal replacement | Alle 2 Betriebsstunden · Ersetzen alle 12 km | Fortgeschritten | Inspect fork operation and check for oil leakage; adjust compression/rebound as needed. Replace fork oil (Suspension oil "01"/"S1") and oil seals. |
| Rear shock absorber inspection, adjustment, lubrication & retightening | Alle 2 Betriebsstunden | Fortgeschritten | Check rear shock operation and adjust; lubricate shock linkage/assembly with molybdenum disulfide grease (after washing the motorcycle or riding in rain); retighten mounting hardware. |
| Chain guard & roller inspection | Alle 2 Betriebsstunden | Einfach | Inspect chain guard, chain roller/slider and drive chain support guide for wear or damage. |
| Swingarm inspection, lubrication & retightening | Alle 2 Betriebsstunden | Mittel | Inspect swingarm pivot bearings for looseness; lubricate with molybdenum disulfide grease; retighten pivot hardware. |
| Relay arm & connecting rod (linkage) inspection, lubrication & retightening | Alle 2 Betriebsstunden | Mittel | Inspect rear suspension relay arm and connecting rod (linkage) bearings; lubricate with molybdenum disulfide grease; retighten. |
| Steering head bearing inspection, lubrication & replacement | Alle 12 Betriebsstunden | Fortgeschritten | Check steering head free play and retighten; clean and lubricate bearings with lithium-soap-based grease. Replace bearings as required. |
| Tire, wheel & spoke inspection; sprocket bolt retightening | Alle 2 Betriebsstunden | Mittel | Check tire air pressure, wheel runout, spoke looseness and tire wear; retighten rear sprocket bolts. |
| Throttle & control cable routing check & lubrication | Alle 2 Betriebsstunden | Einfach | Check throttle and control cable routing/connection; lubricate with Yamaha cable lube or SAE 10W-30 motor oil. |
| Brake fluid replacement | Alle 12 Monate · Ersetzen alle 24 Monate | Mittel | Replace front and rear hydraulic brake fluid. |
Keine Wartungspunkte gefunden, die zu deiner Suche passen.
Einfach: einfache Werkzeuge, unkompliziert Einfach–Mittel: je nach Aufgabe unterschiedlich – irgendwo dazwischen Mittel: etwas technisches Verständnis hilft Fortgeschritten: spezielles Werkzeug/Können nötig, aber noch selbst machbar Experte: deutliche Erfahrung erforderlich Profi: Werkstatt oder Vertragshändler empfohlen
Was steht an?
Gib deinen aktuellen Kilometerstand (km) ein, um zu sehen, was ansteht.
Ähnliche Motorräder
Etwas falsch entdeckt?
Sag uns, was am obigen Wartungsplan für die Yamaha YZ125 (2018) korrigiert werden muss.